Search results

If the CX5 is like most vehicles, turning the temp up doesn't really help the evaporator dry out. The heater core is after the evaporator. All you need to do is turn off the A/C and make sure you aren't in defrost or foot only modes as those run the A/C (temperature permitting). Just set the...

I don't have a CX9, but I have a USB microSD adapter with a 16gb micro SD for my music and it works fine. As youri said, it just sees it as a USB, should work on the CX9 as well. It was something like $10 from Amazon.

Take alternator out and bring to a parts store that tests them. If you have the old alternator, you could bring that as well.

Just a general comment on the wipers, my previous VW Golf and my current Ford Edge both require wipers to be in service position to lift them otherwise they hit the hood. My Golf had to do similar 'electronically' put in service position. My Edge, I can actually just manually rotate the wiper...

(sarcasm) But I don't want the gubberment to know who/where I am or what I'm doing......Typed on my cell phone. :) (end sarcasm).

I agree lug nuts first thing to check. My coworker just went through loose (and missing) lug nuts last week. He had new struts put on and after about a week a bad vibration developed. He thought it might be the struts, but I told him to check wheel lugs first. One front wheel was missing 3 of...

That's a good point. I know on my wife's old CX9, the light cutoff stepped down from right to left (US) as to reduce blinding oncoming traffic on the left side of the car. UK being on the (wrong) other side of the road would need the opposite.

I'm actually surprised a 1/2" (12.7mm) wrench doesn't fit just right if the 12mm is too small and 13mm is too large. I've used a cresent wrench and resorted to a pipe wrench at one time. Vice grips work as well. If you turn each side equal amounts, you should still be pretty darn close to...

I think the title is still accurate. Both pumps failed, but it was due to wiring. The OP could update the title to reference the wiring: "Fuel pumps failed due to wiring." or something like that.

Try pulling the serpentine belt and running it again to see if noise disappears. You should be able to run it for a minute or 2 without worrying about the battery dying.

I'm also in the camp of lifter tick, however, I wouldn't say it's normal. Last time I heard lifter tick that loud was when I started the new engine in my old 89 5.0, but it only ticked for about 10 seconds until all the lifters pumped up. If it is a lifter not pumping up, that might not show...

I don't know the TSB, but if you can find that thread, I believe it was posted in there.

There's a TSB for that.

I agree, if they are louvers, oil flow should not be an issue. Very common design across the automotive universe.

I think he's talking about the perforations on the ID, not the end. It's hard to tell though, they might not be straight through, but more like 'louvered' punches.

Not quite the same, but this is an issue with some 5th gen Ford Explorers. There's a switch in the center console that's the issue. The transmission is in park by the cable, but the switch by the shifter doesn't get triggered so the computer doesn't think it's in park. Maybe you have a loose...

If it's normal, ask them what is causing it and why not all CX5's have this 'normal' behavior. Them (windows/sunroof) working separately doesn't explain why it has this issue when combined. Go at them with the 5 why's for determining root cause.

What type of scope did you use? Are you able to swap that injector to another cylinder to verify it follows the injector? Based on your testing, it does seem like a bad injector, but if you can do a quick injector swap and it follows the injector, that would be another confirmed dead injector test.

I agree with the change to 9011. I don't have a CX5, but my 2014 Explorer specs the 9005 bulb for low/high beams. It has the shutter to cut off the top of the beam in low mode. I think I just had to trim half of the top tab off to get the 9011 bulbs to fit. Takes longer to remove the bulb from...