Say hello to my lil freind!!

[azian6er]

i got some work ahead of me this week!

-B

 

[black_rob00]

Sweet!!

 

[igdrasil]

what is it? forged pistons?

 

[Matthew]

i cant tell because the picture is 1280x960

RESIZE PICTURES FOR GODS SAKE!!!

 

[azian6er]

i cant tell because the picture is 1280x960

RESIZE PICTURES FOR GODS SAKE!!!

sorry no p-shop and i am comp. illiterate.

Anyone who could resize them i would love you forever.

This is my block i just picked up from perfworks. 2mm over bore je pistons pauter rods etc.

-B

 

[black_rob00]

i cant tell because the picture is 1280x960

RESIZE PICTURES FOR GODS SAKE!!!

 

[DiscreetSpeed]

lol meebe this time youll have better luck, and make sure you get that tuned by a pro. and gosh sakes get some advice before u start doing your boostin...lol
happy boostin.

 

[azian6er]

you are a god send.

thanks

-B

 

[azian6er]

lol meebe this time youll have better luck, and make sure you get that tuned by a pro. and gosh sakes get some advice before u start doing your boostin...lol
happy boostin.

thanks for the advice. The haltech is already tuned by juan at high boost for the msp with a bigger turbo. I will have to do some dyno tuning before i really start looking for power, but for the first 800-1K miles i will not see any boost.

Oh and fyi i didnt blow my motor because of boost last time man. I had an oil consumption problem and my rod bearing spun. (boom06)

-B

 

[black_rob00]

you are a god send.

thanks

-B

No problem

 

[DiscreetSpeed]

thanks for the advice. The haltech is already tuned by juan at high boost for the msp with a bigger turbo. I will have to do some dyno tuning before i really start looking for power, but for the first 800-1K miles i will not see any boost.

Oh and fyi i didnt blow my motor because of boost last time man. I had an oil consumption problem and my rod bearing spun. (boom06)

-B

i remember...just hope you have better luck(yes)

 

[igdrasil]

tune that sucka and go for the 12s

 

[azian6er]

well i think i really have the means to do so. I have everything done except for axles and tranny but i believe the tranny will hold well as well as the axles as long as i dont wear slicks and dump the clutch like a crazy mofo.

I think with a built fs, bigger turbo, enough fuel, and ems i should be able to go 12s. I am crossing my fingers at least and hope nothing goes boom!

-B

 

[azian6er]

i remember...just hope you have better luck(yes)

thanks. oh and buy my emanage (attn)

-B

 

[LinuxRacr]

Spun bearing huh? Been there too...2nd motor ago. I wish you the best with this project! I will be "pulling" for you in my area(literally) as I'm sure you will in your hood. (thumb)

 

[azian6er]

Spun bearing huh? Been there too...2nd motor ago. I wish you the best with this project! I will be "pulling" for you in my area(literally) as I'm sure you will in your hood. (thumb)

Remeber when i called you that long time ago? Finally it is culminating! I will mosre than likely have a bunch of Q's for you a bit later.

-B

 

[LinuxRacr]

Cool...Same here..

 

[shaolin]

That's what I had planned... Any type of engine/fuel management planned? You got any estimates for results? I want to know how close the community is to getting to 250-300 whp. If I can get into that margin I'll be happy.

 

[MazdaSpeed0020]

Wow, congrats on the engine. It looks very very nice. I cant wait to see what kind of performance you have with this new set up. What turbo are you running now? I am looking to do this in the future. How much did the pistons and rods cost you if you dont mind me asking.

Matt

 

[Togan]

i dunno anything about pistons but all i can say its new and looks good (yes)