Recent content by diabolicinc

I found this site, and with their performance rebuild kit your guranteed around a 40hp increase. I think im gonna try it out and buy it. My head just cracked today and im gonna rebuild my motor while i have the head off. heres the site.....tell me what you guys think, you think is bs or a good...

the only thing that you will notice is that it will smoke like none other. but make sure you have someone holding the the throttle a little bit or the gas pedal. the hose i told you about is a vacuum line that runs into the intake but it hooks up to a boost sensor i think.you will see a gain in...

sea foam You want to do this: Put about 1/4 bottle in the oil before changing it.... Put about 1/4 in the gas with 93 octane FULL TANK.... Put 1/2 in the vacuum line that connects to a sensor in the back of the intake, it connects to some sensor piece its very small in diameter. your car will...

check this out Run some SEAFOAM in your gas with a full tank of 93 octane, put some in your oil, (make sure your about ready to change it) and run it through a rubber tube that hooks up to a sensor thats connected in the back of the intake(you can take this tube off theres no clamps its very...

ok i have pics on my profile thats as far as i got. and i made it my main picture.

its not a name brand. its just a big intake i installed on my protege awhile back. ive not posted on here in a long time, and maybe thought i could spark up the ole helpless protege! I have a pic but cant figure out how to post the thing. Its actually a brand new APC i think it plastic that...

i have a mad intake on my 98 mazda and it sounds wicked. I also installed a breather were the rubber fitting goes onto the throttle body, gives it a small blow off valve sound at high rpms. Will post pictures tomorrow.

I have a 98 pro, with the 1.5, when i drive the car at 40 miles an hour and go to a stop and put the car in N at a stop light, my rpms drop to where the car is gonna die, then i pops back up to around 800 rpms, then drops again, and when i turn the steering wheel while idling in park, the idle...

valve cover gasket the valve cover gasket is still new it has around 17,000 miles on it. it leaks right under the distributor. I think i have to replace the distributor gasket. I dont know. The transmission is fine, its been service regularly, and its a 5 speed. If not i think i didnt tighten...

Ive recently bought a magazine that has all of the new parts for 2007 for all the imports. I recently was looking and i noticed that TODA RACING has engine parts for the the B6/BP motor, i know that they are miata parts in the magazine, but would the parts fit into a protege bp motor? Please...

I have a small leak around the distributor, i have a 1.5 lx. ive replaced the o-ring, and it still leaks. i burn about a quart of oil around a 750 miles+ give or take.

98 pro for sell, email for pics. 3000.00 diabolicinc@yahoo.com

air intake. I used an APC intake from a 98+ honda accord, I went back to stock because it did nothing at all for the car so i left a small piece of the intake on and had a cone filter left on. I had to cut half of the intake but it worked. and used 2 rubber fittings, one like a 2 1/2 to 3...

1st, 2nd, 3rd generation proteges. If you live in the 502/812 area code of louisville kentucky, or southern indiana. please contact me. i would like to get a sortof club together. Mazdas are not the usual car in my area. Its hondas, and nissans. SO if anyone is interested they can call me or...

Japanese parts You say you have a japanese parts catalog? Well i need some contacts to get ahold of japanese parts for my protege, as well as distribute them in my area. I want to get a conversion kit as of right now for my pro to make it right hand drive. but if anything could you email me on...